Juniper srx show mac address on interface

In the same window on the top right select Tunnel IP in the drop down menu and click new. In this figure you can click edit button on the right and configure the IP addresses. After login into SSG20 expand Network and further expand interfaces and select List. Configure the IP addresses to the corresponding interfaces like we did in SRX. Now, letвЂ™s get into SSG20.ДЇirst of all, login to the SSG web management via web browser. The configuration for SRX 210 is finished.

Note: вЂ“ Make sure that you have allowed both remote network 192.168.100.1/24 and 192.168.10.0/24 network for incoming traffic on the home network. set security policies from-zone trust to-zone untrust policy allowALL match source-address any set security policies from-zone trust to-zone untrust policy allowALL match destination-address any set security policies from-zone trust to-zone untrust policy allowALL match application any set security policies from-zone trust to-zone untrust policy allowALL then permit set security policies from-zone untrust to-zone trust policy fromInternet match source-address any set security policies from-zone untrust to-zone trust policy fromInternet match destination-address any set security policies from-zone untrust to-zone trust policy fromInternet match application any set security policies from-zone untrust to-zone trust policy fromInternet then permit set security ipsec proposal P2proposal protocol esp set security ipsec proposal P2proposal authentication-algorithm hmac-sha1-96 set security ipsec proposal P2proposal encryption-algorithm des-cbc set security ipsec proposal P2proposal lifetime-seconds 36000 set security ipsec policy P2policy perfect-forward-secrecy keys group2 set security ipsec policy P2policy proposals P2proposal set security ipsec vpn site1-to-site2 bind-interface st0.0 set security ipsec vpn site1-to-site2 ike gateway P1gateway set security ipsec vpn site1-to-site2 ike ipsec-policy P2policy set security ipsec vpn site1-to-site2 establish-tunnels immediately Now create security policy to allow traffic from site1 to site2 and vice-versa.

set security ike proposal P1proposal authentication-method pre-shared-keys set security ike proposal P1proposal dh-group group2 set security ike proposal P1proposal encryption-algorithm des-cbc set security ike proposal P1proposal lifetime-seconds 86400 set security ike policy P1policy mode main set security ike policy P1policy proposals P1proposal set security ike policy P1policy pre-shared-key ascii-text set security ike gateway P1gateway ike-policy P1policy set security ike gateway P1gateway address 2.2.2.2 set security ike gateway P1gateway dead-peer-detection interval 10 set security ike gateway P1gateway dead-peer-detection threshold 3 set security ike gateway P1gateway external-interface ge-0/0/0 After configuring the phase 1 IKE, now configure phase 2 IKE configurations. LetвЂ™s now configure phase 1 IKE configuration. set interfaces ge-0/0/0 unit 0 family inet address 1.1.1.1 set interfaces ge-0/0/1 unit 0 family inet address 192.168.4.1/24 set interfaces st0 unit 0 family inet address 192.168.10.1/24 Configure the routing options set routing-options static route 0.0.0.0/0 next-hop 1.1.1.2 set routing-options static route 192.168.100.0/24 next-hop st0.0 Then configure the security zones and interfaces and inbound traffic set security zones security-zone untrust tcp-rst set security zones security-zone untrust host-inbound-traffic system-services all set security zones security-zone untrust interfaces ge-0/0/0.0 set security zones security-zone untrust interfaces st0.0 set security zones security-zone trust tcp-rst set security zones security-zone trust host-inbound-traffic system-services all set security zones security-zone trust interfaces ge-0/0/1.0 Set the IP addresses on the SRX device for public, private and tunnel interface. The diagram below shows two sites, site 1 and site 2 with static IP addresses configured. Static Site to Site VPN in Juniper SRX and SSG Here, I will show static site to site VPN in Juniper SRX and SSG. VPN between two different platform can be difficult. The basic requirement for static site-to-site VPN is static public IP address in both ends. Static site to site VPN is different from dynamic site to site VPN.

Juniper srx show mac address on interface